Beginner's Plumbing: The Essentials for Bathtub Installation

Contact Us


They are making several great annotation on A Step-by-Step Guide to Installing a Bathtub as a whole in this content further down.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bathtub isn't precisely brain surgery, however it does require strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you need to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as set in the new one. Ensure you have actually qualified yourself for the work and are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you might need a specialist plumber to make tube connections.
This post will assist you mount a new tub in your washroom if you have currently gotten a brand-new bathtub as well as do not need to transform the plan of your previous water system pipelines.
Your devices and also product checklist should consist of the following:


  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  •  

Preparing for the Installation


First of all, the supporting framework provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last position.



Removing Old Taps


If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will certainly come from the pipes. When the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.



Setting up the Tub


Using both wooden boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub until the level checks out level.
To set up faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water supply and also examine all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and additionally inspect the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the tub has actually been made use of a minimum of when as this will resolve it right into its final placement.



Fitting New Touches


If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Protect the faucet in place with the manufacturer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.



Tiling Around the Bathtub


In the area where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to crack an inflexible seal, creating the water to permeate the wall surface in between the bath and also the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water resistant sticky and also grout.


A Step-by-Step Guide to Installing a Bathtub


Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


Remove the Existing Bathtub


To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


Choose the Right Bathtub


The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


Install the Plumbing and Ledger Board


You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


Install the Bathtub


When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


Hook up the Plumbing


Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


Install the Bathtub Surround


A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


A Step-by-Step Guide to Installing a Bathtub


Do you like reading up on Installing A Bathtub? Leave a comment down the page. We will be delighted to listen to your responses about this article. In hopes to see you back again before long. Sharing is nice. You won't know, you might be helping someone out. Thanks so much for going through it.


Immediate response? Click here.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Beginner's Plumbing: The Essentials for Bathtub Installation”

Leave a Reply

Gravatar